Gjysmë rimorkio me tendë i ri Meusburger 4-Achs-Jumbo-Sattelauflieger mit Planenaufbau

Frame:

Welded steel frame construction – lightweight design

Frame neck ca. 110 mm – not height-adjustable

2“-king pin

Front installation dimension according to front corner measure of 2.040 mm

supporting U-beam-outer frame (strength 6 mm) for light contruction machines with a tare weight not over 17 tons

rear underrun = extended endplate

mounting rail for ramps at the rear at the endplate

prop stands at the rear

Landing legs:

Mechanical 24 to landing legs with single sided operation

Axles:

BPW-air suspension-axles (each axle with an axleload of 9 tons)

S-cam break 300/200 mm, asbestos-free brake pads

Autom. Brake adjuster

Lowering and Lifting with a total stroke of ca. 190 mm

1st axle as lifting axle, Betätigung vollautomatisch mit mechanischer Notbetätigung über Taster am Auflieger

3rd and 4th are self steering axles with electrical and mechanical lock (automatic locking of the steering of the 3rd axle when the 1st axle is lifted)

Rims and wheels:

18 steel wheels, 10-holes, with offset, centered

18 wheels 205/65 R 17,5 132/132F, tubeless.

Mudguards:

Mudguards of steel sheet with Clear Pass

Braking system:

Two line brakes with EBS

EBS-braking system (WABCO 4S3M)

Aluminium air tanks

Spring controlled parking brake

Electrical equipment:

In accordance with automotive law

24 Volt. 1x 15-pin + 2x 7-pin sockets

2x 7-chamber-rear lights in the endplate

1x holder for warning light at the rear

Side marker lights (LED)

Floor:

Glued laminated cast layer (27 mm)

DIN rails next to the longitudinal beams and with support at the outer frame = flush with the outer frame and the longitudinal beams

Covering of metal sheet over the wheels

Front panel:

Aluminum hollow sections (25 mm) till the lower edgs of the roof with integrated curtain buckles

Curtainsider:

Curtainsider on both sides with shrink-wrapped vertical and horitontal straps (distance ca. 600 mm) and curtain buckles of stainless steel

adjustable tarpaulin straps (with other-centre toggle mechanism)

tarpaulin extensions included with push button and velcro fasteners

tarpaulin extensions in direction of travel: ca. 300 mm, in height: ca. 1.000 mm

eyelets for loose tarpaulin parts included (but without extension)

2 pairs of vertical tarpaulin bags with a legth of ca. 1.300 mm, positon in the low deck at the front and the rear crank

Small bags for tarpaulin straps

Rear panel:

Steel rear portal frame with lateral suspension device for the tarpaulin

Aluminium-double-wing doors (25 mm)

Both door leaves fully convertible with door-stay

Each door leaf with aluminium double joint-hinge and two embedded recessed grips

Rear panel with side extension of ca. 1.250 mm on each side mechanical through crank

Front corner posts:

In roof height, bolted on the face

Middle posts:

3 pairs of posts – stepless movable

The posts are movable over the whole length through trolleys and lockable at every position

Roof:

EDSCHA-sliding roof (galvanised) with lateral bowsmovable in 1 direction (compressed to the front in the cargo space), without tendency

The rear panel-crossbeam is pivoted

PVC-tarpaulin roof without custom seal

Lifting roof is on both sides adjustable mechanically, stroke: 300 mm

Lifting roof is mobile in an increased position - front (+8x 50 mm) and rear (+9x 50 mm)

Roof can be decreased at the front to a total height of 3.950 mm

Tarpaulin extension included and tarpaulin bib at the rear

Edscha-sliding rails at the front on both sides can be extended mechanically (900 mm)

Painting:

Cleaning with steel pellets and priming

Painting chassis and hubs: in RAL

Outer frame, landing legs and posts: in RAL

Front and rear panel in RAL 9006 silver

tarpaulin in RAL 9006 silver

rims in silver

plastic parts black unpainted

without labelling

lateral part-marking over the buckles and at the top in the corners in yellow

full marking at the rear in yellow

Additional equipment:

4 wheel chokes with holder at the front panel

Licence plate holder at the endplate

2 ECE-sheets

Side underrun guards (aluminium)

12 pairs of lashing rings embedded in the outer frame (each of 4 tons)

7 pairs of heavy load-lashing rings (foldable / each of 8 tons)

2 pairs of spare wheel holder with winch at the front panel

3 rows of bows (aluminium), self-locking hooks included Extendable warning plates with position lights, stepless extendable till a cargo width of 5.000 mm

1 PVC-tool box (500x300x450 mm)

Deposit for ramps behind the last axle

Ladder (aluminium) with holder at the front panel

Night parking panel and ADR-panel at the rear panel